Mac & Matco Tool Truck Soap Holders & Display
Soap Holders Sized to the Bottles You Actually Carry
Mac HC2.5 and Matco Xtreme Clean cartridges, plus the 14oz pump bottles — mounted upright, label-out and locked in through every stop. Screw-mount, PETG, made in the USA.
Shop Soap HoldersSoap Holders · Fits Mac & Matco Hand Cleaner
New for Mac and Matco routes. Pick the bottle you stock — each holder is modeled around that exact container.
85oz Soap Holder · Matco Xtreme Clean
Square pocket sized to the 2.5L Xtreme Clean cartridge. Label faces out, open bottom clears the nozzle.
85oz Soap Holder · Mac HC2.5
Round sleeve sized to the 2.5L HC2.5 Industrial Hand Cleaner. Label faces out, open bottom clears the nozzle.
Dual 14oz Soap Holder
Two 14oz pump bottles side by side, either brand. Snug cutouts keep them upright on the wall.
Display & Cab
Impulse buys at eye level, and the cab pieces that keep the front seat squared away. Works on any truck.
Snack Holder
Two pockets for jerky and beef sticks, mounted up where customers see them. 8" wide.
Butane Torch Holder
Showcases three or five butane torches at once. Wall-mountable, black.
Flashlight Display · Holds 10
Ten flashlights upright and facing the customer. Fits Olight Ark, Ark Pro and Arkfeld, plus Coast Elite and Slayer.
Door Caddy
Velcros onto the door and holds your phone, wallet or whatever rides up front.
Cupholder Insert
Press-fits the oversized cupholder in Freightliner S2RV/M2 and International MV cabs. Black fits 8–16oz cans; red fits 20oz and large tumblers.
What You're Actually Buying
The same spec applies to every holder on this page.
Each soap holder is modeled around a specific container — the Matco Xtreme Clean 2.5L cartridge, the Mac HC2.5 2.5L cartridge, or two 14oz pump bottles from either brand. Snug fit, easy in and out.
Multiple screw points on every holder. Drives into walls, shelving or your toolbox — no adhesive pads that let go in summer heat.
PETG — impact-resistant and heat-tolerant, printed to handle the bumps and daily abuse of a working route truck.
Made in the USA, in small batches, to order.
Printed and shipped in 3–5 business days. If it's going to take longer, we'll email you before it ships, not after. Free shipping over $99.
Free returns on any undamaged, unmodified product.
Soap on Its Side Doesn't Sell
Every pothole shuffles your truck. A cartridge that's been rolling around the floor looks like a cartridge that's been rolling around the floor. Mounted label-out at eye level, it's an impulse buy at every stop.
- Locked in on the move. Cartridges and bottles stay upright through every turn.
- Sized for Mac and Matco. Modeled on the actual containers — not a generic cup.
- Label-out merchandising. Customers see what it is before you say a word.
- Screw mount. On the wall in minutes, stays there for good.
Common Questions
Which holder fits which soap?
The square holder fits the Matco Tools Xtreme Clean 85oz (2.5L) cartridge. The round holder fits the Mac Tools HC2.5 85oz (2.5L) cartridge. The dual holder fits two 14oz pump bottles from either brand. They're not interchangeable — the Mac and Matco cartridges are different shapes.
Does the cartridge dispense while it's in the holder?
Yes. Both 85oz holders are open at the bottom so the nozzle and cap hang clear — mount it, drop the cartridge in, and it's ready to use.
How do they mount to the truck?
Every holder has multiple screw points. Drive screws into your wall, shelving or toolbox and it's on there for good. The door caddy is the exception: it Velcros on so you can pull it off when you need to.
How long until it ships?
The soap holders are printed to order and ship in 3–5 business days. If it's going to take longer than that, we'll email you before it ships, not after.
What are they made of?
PETG — an impact-resistant, heat-tolerant plastic that holds up to summer truck temperatures far better than standard PLA.
I run Snap-on. Do you make those too?
Yes — the Snap-on Black Cherry holders (18oz, 64oz and 84oz) have their own page. Shop Snap-on holders.
Do you make custom holders?
We regularly build new holders for the tool truck world — if there's a product you want secured or displayed, reach out through our contact page.
Get the Soap Off the Floor
Pick the holder that matches the cartridge you stock, screw it to the wall, and stop chasing loose product every stop.
iPrint3D Company is not affiliated with or endorsed by Mac Tools, Matco Tools, Snap-on Incorporated, Olight, Coast, Freightliner or International. Product names are used solely to indicate compatibility.